Setup Wizard

From Edge Threat Management Wiki - Arista
Jump to navigationJump to search

The Setup Wizard will open automatically when Untangle first boots. If you do not have a keyboard/mouse/video connected to the Untangle server, the Setup Wizard can be reached by plugging into a DHCP-configured laptop into the internal interface opening a browser to http://192.168.2.1/.

Once installed, the setup wizard can be repeated at any time and can be found in the NG Firewall GUI at Config > System > Support > Setup Wizard.

Language selection

Before you begin the setup wizard, select your preferred language.

Setup Wizard - Select language
Setup Wizard - Select language

Setup Wizard - Welcome

The next screen simply welcomes you to the Setup Wizard. Click next to continue.

Setup Wizard - Welcome
Setup Wizard - Welcome

Setup Wizard - Step 1 - Configure the Server

The first step has you set a password for the administrator account and select a timezone. You can also set the admin email to receive alerts and reports. The installation type is optional.

Setup Wizard - Step 1
Setup Wizard - Step 1

Setup Wizard - Step 2 - Identify Network Cards

The second step shows you the network cards. If this is an appliance from Untangle you can simply continue to the next step. If this is a custom server, verify that the physical network cards are mapped to the correct (desired) interface. You can verify connectivity by disconnecting or connecting the cable to the physical interface. The status icon changes immediately between grey or green to show the link state.

Setup Wizard - Step 2 Remapping
Setup Wizard - Step 2 Remapping

Setup Wizard - Step 3 - Configure The Internet Connection

The third step configures your External (WAN) interface.

Setup Wizard - Step 3 Auto
Setup Wizard - Step 3 Auto

The default selection is Auto (DHCP). The automatically assigned address is displayed if an address was successfully acquired. Otherwise, click Renew DHCP to acquire an IP address. Click Test Connectivity to verify Internet access.

If your Internet connection requires a static IP address or uses PPPoE, select the appropriate option and enter the parameters assigned by your Internet Service Provider.

Setup Wizard - Step 4 - Internal Network Interface

The fourth step will configure your "Internal" interface (and DHCP server and NAT configuration.) There are two choices.

Setup Wizard - Step 4
Setup Wizard - Step 4

You can configure the internal interface with private static IP address (ie 192.168.2.1) and enable DHCP serving and NAT (Network Address Translation) so all internal machines will have private addresses and share one public IP. This is commonly referred to as Router mode.

You can also configure the internal interface to be bridged to the external. In this mode the internal interface does not have its own address and is simply shares the External's address. This is commonly referred to as Transparent Bridge mode.

Router

In Router mode, Untangle will be the edge device on your network and serve as a router and firewall. In this case you'll need to set up your External and Internal interfaces correctly for traffic to flow, which should have been done while installing.

File:Router mode.png
Untangle in Router mode

Transparent Bridge

In Transparent Bridge mode, Untangle is installed behind an existing firewall and sits between your existing firewall and main switch. When in Bridge mode Untangle is transparent, meaning you won't need to change the default gateway of the computers on your network or the routes on your firewall - just put the Untangle between your firewall and main switch and that's it. You do not change the configuration of existing clients or the existing firewall!

File:Bridge mode.png
Untangle in Bridge mode

Setup Wizard - Step 5 - Configure Automatic Upgrade Settings

In the fifth step Automatic Upgrades are configured. If Automatic Upgrades is enabled will automatically check for new versions and upgrade automatically between 1am and 2am every morning.

Setup Wizard - Step 5
Setup Wizard - Step 5

Setup Wizard - Finished

That's it!

Setup Wizard - Congratulations
Setup Wizard - Congratulations

The next step is installing the desired applications and possibly further tuning the configuration of your Untangle server, then actually dropping Untangle into the network if it is not already in place.

Remember, the setup wizard can be repeated at any time. In Config > System > Support, click Setup Wizard.